Easier to Read Pro-97/2055 Scanner Manual

Click here to buy a printed, bound, formatted in color, copy of this manual from Scanner Master

Home

Last Updated October 26, 2019  

Contents
Introduction Scanning and Trunking Banks
Main Features   Changing Open and Closed Modes
Scanning Terminology   Turning ID Scan Lists On and Off
Understanding Trunking   Locking/Unlocking IDs
Understanding Banks   Switching Text and ID Code Display
Understanding IDs   Switching EDACS Format Display
Receive Modes Searching for Frequencies
Understanding CTCSS/DCS   CB, Marine, or FRS/GRMS/MURS Search
Open and Closed Modes   Police/Fire, Air, or Amateur Search
Keypad and Knob Controls   Service Search Band Charts
Setting the Squelch   Seek Function
A Look at the Display   Limit Search
  In Scan Mode   Tune Search
  In Receive Mode   Frequency Copy
  In Search Mode   Zeromatic Tuning
  In Signal Stalker Mode   Locking/Unlocking Search Frequencies
Programming Conventional Frequencies Weather Radio
  Deleting Frequencies   Listening to the Weather Band
  Programming Tone Codes   Receiving SAME Weather Alerts
Programming Trunking Systems   Skywarn Programming
  Programming a Fleet Map Special Features
  Fleet Maps   Text Tagging
  Programming Offset and Base Frequency   Turning the Keytone Off and On
Programming Talk Group IDs   Backlight/Dimmer
  Changing ID Delay   Changing the Display Contrast
  Clearing IDs   Keylock
Signal Stalker II   Cloning/Uploading/Downloading
  Special Signal Stalker   Scanner Reset
Scanning Conventional Banks   Automatic Power Save
  Changing Receive Modes   Viewing/Updating Firmware
  Using the Attenuator Related Links/Info
  Priority Scanning    
  Locking/Unlocking Channels    

Introduction Contents
These are another excellent set of radios that have many fine features for scanning and trunking. However, anyone who has tried to read the manuals that come with the radios know it can be a little hard (if you're lucky) to find, read, and figure out some of the steps, especially in the searching and trunking sections. IMHO they are a mess.
 
I can’t remember everything and find myself referring back to the manual for explanations of procedures and find it frustrating trying to figure out the wording every time. I decided to write and publish this for myself to make it easier to use the radio and am happy to share it with you. This should also make it easier for most people to use some of the more advanced features of the radio (and get their money’s worth if you paid full-price for the radio new) as I will try to explain procedures a little more clearly and in a more logical order. Granted, these radios aren't simple so you will have to spend some time on them but this manual will at least make it easier. If you follow the red highlighted text in the programming sections, you should find what you need to know. If you want to find out what's really going on with the radio, read everything else.
 
Some of the better features of these radios are the ability to receive tone codes in certain service searches, the seek feature in search mode that resumes searching after 5 seconds, and the adjustable ID delay. IDs can be locked out in open mode (vs. the older Pro-93/2053/94/95). The Skywarn lets you program 3 Skywarn frequencies (or any other conventional freqs) into channels 997-999 for one-touch access to them. The Repeater Finder Tool will help you find the correct LCN for LTR systems. The best one, in my opinion, is the ability to configure everything in the software, on the computer, and then just shoot it to the radio (with a one-way cable) or back to the computer (with a two-way cable). Much easier to work with the keyboard and see the monitor. You can set the attenuator globally or per channel. With a couple of keystrokes, you can view the IDs as text or code. There are 5 ID lists (30 IDs per list) to store 150 IDs for each bank.
 
Now, on the flip side, there are some pretty annoying things about these radios too. They still have preset steps that will not tune to many of the splinter frequencies in the VHF range (except the 108-137 air band) like 151.0125; (it accepts it as 151.01). The Air service search is relatively slow because of the 8.33 kHz steps. Still only 1 priority channel? The backlight goes out long before the batteries die.

An overview of the features can also be viewed at my
Trunking Radio Comparison Chart page.

You will also need a better antenna. The stock rubber duck isn't fabulous.
RS has the Center-Loaded Telescoping Whip for $15 - better for VHF/UHF. The 800MHz Scanner Antenna  for $25 - 100% better for 700+ MHz. You may be able to find others on the web but RS is convenient so you can buy it and take it back in the same day if you don't like it. Read the reviews for each at the site.
 
These radios also have software that will enhance and/or enable other features not possible with just the keypad and have been noted when known. My opinion is get the software if you have a lot of frequencies. With all the features and setting in these new fangled devices it will save you hours of programming and frustration. It may also be easier to figure out the software than the keypad sequences. Alpha tagging is great but much easier with the software. Because of the limited amount of keys on the radios, programming a 3 letter word takes about 20 keystrokes on my Pro-97, if you can remember the sequence and don't make a mistake, after you program the bank name. See what I mean? Get the software. You have to dish out $20 bucks or so for a cable, the software is $20-30 (after a 30-day free trial), and there are plenty of newsgroups on the Net about these radios to help you hook up to the computer and work the software.
 
All in all, they will compliment your scanner collection (provided you have one).

I will assume you know how to obtain the basic information from the original manual such as following safety procedures, putting the batteries in, connecting the antenna, finding specs, etc. and concentrate on the main functions of the scanner.
 
I hereby absolve myself from anything that happens to anyone or the scanner as a result of the information you will be reading. You are welcome to copy and/or print these pages and use them in the scanning hobby as long as you don't change, redistribute, or charge/accept money for them.
 
Check back often as this document will be updated and revised from time to time. I have tried the best I can to make sure everything is accurate here but if I missed a step or you see something that's obviously wrong, please email me.

Main Features Contents
Multi-System Trunking - you can track Motorola, EDACS (GE/Ericsson), and LTR trunking systems.
Control Channel Only Scanning - automatically determines the trunking frequencies for Motorola trunking systems only, once the control channels are programmed.
Repeater Finder Tool - displays the current Home Repeater when monitoring LTR transmissions in manual mode.
Data Cloning - lets you transfer the programmed data from one Pro-97/2055 to another Pro-97/2055. You can also download the programmed data from a PC to the scanner (using an optional one-way PC cable), or upload the programmed data to the scanner (using a two-way PC cable) with the optional software.
Simultaneous Trunk and Scan - scans conventional and trunked frequencies together at the same time.
16 Character, 4-line, Dot Matrix Text Display - lets you program a text label for each channel, bank, talkgroup ID, or a limit search so you can easily identify the transmission.
Trunking ID Delay - variable delay (1/2 to 4 seconds) before searching for another talkgroup ID so you can hear more replies that are made on the same talkgroup ID.
6 Service Search Banks - Marine, CB, FRS/GMRS/MURS, Police/Fire, Aircraft, and Amateur pre-programmed search ranges and 1 programmable limit search to reduce search time and monitor interesting frequencies more quickly.
Tune Search - The scanner will allow you to start searching up or down from a specific frequency.
Search Lockouts- for each channel in the CB, Marine, and FRS/GMRS/MURS bands and 50 per band for each of the, Air, Police/Fire, Amateur, or limit search bands.
Attenuation - lets you program your scanner (per channel or globally) to reduce the scanner's sensitivity to strong local signals or noise caused by these signals to reduce interference.
10 Channel Storage Banks - you can store up to 100 channels in each bank.
HyperSearch and HyperScan - searches up to 100 steps per second and scans up to 50 channels per second.
10 ID-Storage Banks - lets you store and/or lock out 1500 IDs in 10 ID banks that have 5 sub-ID banks of 30 each. Each sub-bank can be turned on or off so you can monitor ID's you prefer.
Channel Lockouts - lets you lock any channel in any bank.
Weather Alert - can be set to automatically sound the alarm tone to advise of hazardous weather conditions when it detects the alert signal on the local National Oceanic and Atmospheric Administration (NOAA) weather channel (SAME standby mode) or you can also scan and set the weather channel as a priority channel. Displays the weather event text with four alert levels so you can see and hear the reason for the alert. Also has 3 programmable Skywarn channels.
Triple-Conversion Circuitry - virtually eliminates (depending on your location) any interference from IF (intermediate frequency) images, so you hear only the selected frequency.
Backlit Keypad and Display - select the time the light stays on or set to constant.
Three Power Options (Pro 97) - lets you power the scanner using internal batteries; alkaline, Ni-Cad, or Ni-MH; external AC power using an optional 9 volt 300-mA AC adapter/charger (and RS ‘type C’ adaptaplug); or DC power using an optional 9 volt DC cigarette-lighter power cable.
Scan/Search Delay - 2 second (adjustable delay with optional software and cable) scan and search delay before moving to another channel, frequency, or trunking system so you can hear more replies that are made on the same transmission.
1 Priority Channel - lets you program an additional frequency, one of the conventional channels, or a weather channel and then have the scanner check that channel every 2 seconds while it scans the bank, so you don't miss transmissions on that frequency or channel.
Manual Access - lets you directly access any channel or frequency.
Key Lock - lets you lock the scanner's keys to help prevent accidental changes to the scanner's programming.
Battery Low Alert (Pro 97) - warns you when battery power gets low by beeping about every 10 seconds.
Key Confirmation Tones - the scanner sounds a tone when you press a key, perform an operation correctly, and an error tone if you make an error. Can be turned off.
Memory Backup - keeps the frequencies stored in memory for an extended time if the radio loses power.
 
Your scanner can receive these bands:
 
Frequency Range Step (kHz)

Mode (Default)

Band Frequency Range Step (kHz)

Mode (Default)

Band
25-28 5 AM CB, VHF Lo Band 157.4775-161.565 7.5 FM Police-Business-Rail
28-54 5 FM 10m/6m Amateur 161.570-162.020 5 FM Remote Broadcast-Maritime
108-137 8.33 AM Civilian Air 162.025-173.200 12.5 FM Government Band
137-138 5 FM Satellite 173.20375-173.2225 6.25 FM Government Band
138-144 12.5 FM Government 173.225-173.3875 6.25 FM Government Band
144-148 5 FM 2m Amateur 173.390-173.40875 6.25 FM Government Band
148-150.775 12.5 FM Government-Satellite 173.4125-174 12.5 FM Government Band
150.7825-150.8125 7.5 FM Auto Emergency 216.0025-220 5 FM Maritime
154.45625-154.47875 7.5 FM Fire-Business 220-225 5 FM 1.25m Amateur-General Trunked
154.4825-154.505 7.5 FM Industry 225-406 25 AM Military Air-Military Trunked
154.510-154.525 5 FM Industry 406-512 6.25 FM 70cm Amateur, UHF TV
154.5275-154.54625 6.25 FM Industry 806-823.9875 6.25 FM Mobile Trunked Public Safety
154.5475-154.6075 7.5 FM Industry 849-868.9875 6.25 FM Base Trunked Public Safety
154.610-154.655 5 FM Police 894-940 6.25 FM 33cm Amateur-Business Trunked
154.6575-156.2475 7.5 FM Police 940-960 6.25 FM Government-Broadcast
156.250-157.475 5 FM Maritime 1240-1300 6.25 FM 23cm Amateur-Government

Scanning Terminology Contents
 
Note: To avoid confusion, and to also correct RS, I will be referring to the pre-programmed search ranges as bands and not banks. A band is something you search; a bank is where you store things (like channels). The RS manual will refer to search bands as 'bands'; (correct), 'banks', 'frequency ranges' or 'search ranges' to really confuse people.
Scanning- the process of stepping through conventional channels in scan banks.
Trunktracking (open mode)- the process of searching for all active talkgroup IDs in trunked systems, in scan banks.
Trunkscanning (closed mode)- the process of stepping through programmed talkgroup IDs in ID lists, in trunked systems, in scan banks.
Open and Closed Modes- You search all IDs in Open mode or just programmed IDs in Closed mode.
Pause Mode- the mode the radio is in while paused on a scan; service, limit, or tune search.
Searching- the process of searching for active frequencies in pre-programmed service searches, programmed frequency bands, or the limit search.
Manual Mode- used for browsing and monitoring a channels.
Program Mode- used for storing frequencies, limit searches, priority channels, trunking frequencies/systems/fleet maps, and talkgroup ID lists.
Trunk Mode- used for trunking and programming trunking frequencies and functions.
Clone Mode- used for cloning scanners and uploading/downloading to/from scanners using a computer.
 
At certain times, the radio can be in more than one mode at a time such as program and trunk mode to program trunked functions.

Understanding Trunking Contents
Trunking systems let a large group of 2-way radio users (or even different groups of 2-way radio users) efficiently use a set of frequencies. Instead of selecting a specific frequency for a transmission, the user’s radio selects a programmed trunking bank in the system when that user presses their PTT (push to talk) button. The trunking system automatically transmits the call on the first available frequency, and also sends (on a different frequency called a Data or Control channel) a code that uniquely identifies that transmission as a talkgroup ID (or just ID.) So when you are trunktracking a system, you are listening to active IDs transmitting in the system (each using the first available frequency in the system.) Trunking systems in general allocate and use fewer frequencies among many different users.

Since the trunking system might send a call and its response on different frequencies, it is difficult to listen to trunked communications using a conventional scanner. These scanners let you monitor the control channel frequency so you can hear calls and responses for users and more easily "follow" conversations than with a conventional scanner.

These scanners trunktrack the following types of systems:
  • Motorola Type I
  • Motorola Type II
  • Motorola Type IIi Hybrid
  • Motorola Type II Smartnet
  • Motorola Type II Smartzone
  • Motorola Type II Smartzone Omnilink
  • EDACS Standard (Wide)
  • EDACS Networked (Wide)
  • LTR Standard
When you program Motorola and EDACS system frequencies into the scanner, one frequency is the control (or data) channel, and the rest are voice frequencies shared by all the users. There may be 3 or 4 frequencies assigned as (primary or alternate) control channels but only one control channel will be active at a time. These scanners will allow you to program just Motorola control channels into the trunking system and the voice channels will automatically be found (but not programmed). EDACS systems need all the frequencies for the system programmed and in the correct LCN (Logical Channel Number) order.

The control channel is continually transmitted to the field units and has a sound similar to listening to a boat engine over the phone (in manual mode; you won't hear this when you are trunking the system.) This control channel is also a good check to see if you can trunktrack the system. If you can't hear a control channel when you step through the trunking frequencies (in manual mode), you either don't have all the frequencies or are too far away to receive the control channel and the system.
Motorola systems are limited to a maximum of 28 frequencies per system or site. Ericsson EDACS systems are limited to 25 frequencies per system or site. Motorola and EDACS systems can be either analog, digital, or mixed (digital and analog talkgroups). These scanners can't monitor digital systems.

LTR systems work a little differently. LTR systems typically do not have a dedicated control channel.
This type of system encodes all trunking information as digital subaudible data that accompanies each transmission. The frequencies also have to be in LCN (Logical Channel Number) order or the correct 'slot' for the system to trunktrack properly. The Repeater Finder Tool will help you determine the correct order. Each repeater has its own controller, and all of these controllers are synchronized together. Even though each controller monitors its own channel, one of the channel controllers is assigned to be a master that all controllers report to. Each of these controllers sends out a data burst approximately every 10 seconds so that the subscriber units know that the system is there. This data burst is not sent at the same time by all the channels, but happens randomly throughout all the system channels. If you listen to the frequencies of an LTR system in manual mode (not trunking), on every channel in the system you will hear this data burst that will sound like a short blip of static like someone keyed up and unkeyed a radio within about 500 msec. LTR systems are limited to 20 frequencies per system.

Trunkscanning is basically scanning IDs that are programmed into ID locations (same concept as frequencies into channels.) You can then trunkscan just the programmed IDs. Trunktracking is searching for all IDs in a system (same concept as searching for frequencies in a band.)
 
Radio Reference.com has an excellent page explaining the various types of trunking systems in more detail here.

Understanding Banks Contents
Channel Storage Banks
The radios have 10 banks of 100 channels. Channel numbering starts with 000 and goes to 099 in the first bank. Banks number 0-9. You can also program your trunking frequencies and conventional frequencies into the same bank as well to utilize channel space better.
 
Use each channel-storage bank to group frequencies, such as those for police, fire, ambulance, aircraft, and/or trunking systems. For example, your police department might use 20 frequencies while the fire department uses 15 and a trunked EMS systems uses 5 trunked frequencies. You could program the EMS frequencies starting with channel 000, (the first channel in bank 0), the police frequencies starting with channel 005, and the fire department frequencies starting with channel 025. EDACS systems have to start at channels 001, 101, 201, etc. and follow a LCN order but you can still use 000, 100, 200, etc. for a conventional frequency.
 
For each trunking bank, you can put in one EDACS system (with conventional frequencies), or one Motorola system and/or an LTR system (with conventional frequencies). However, if you store a Motorola system and an LTR system in one bank, the bank mode has to be set to MO (Motorola). If it is set to LT (LTR), the Motorola control channel will break the squelch and hang the scanner on that channel.

Also,
(1)
if you scan this bank in open mode, you will hear all Motorola IDs and LTR transmissions (IDs will be incorrect because the bank is set to receive Motorola IDs).
(2) If you scan this mixed bank in closed mode with Motorola IDs programmed, you will hear just the programmed Motorola IDs.
(3) You will hear the data bursts from the LTR system about every 5 seconds so you should set the delay for these channels accordingly.
 
Tip: Theoretically, you could also program more than one (of the same type i.e. Motorola) trunking system into a bank as long as you could only monitor one at a time, in different locations, far enough apart, so the system you are monitoring wouldn't interfere with the other system (which would confuse the radio). But remember, the scanner can be set to decode only one type of ID (MO, ED, or LTR) per bank.

Service Search Bands
The scanners also have 6 service bands pre-programmed with frequencies and 1 limit search to allow you to create your own search band. Search bands SR3 (Police/Fire), and SR5 (Amateur) are divided into groups or sub-bands of frequencies that can be turned on or off within the bands.

Understanding IDs Contents
Motorola IDs come in two formats: Type I and Type II. Each format displays and uses Talk Group IDs in slightly different ways. Type I/II hybrid systems use both Type I and Type II formats for Talk Group IDs.
 
Type I IDs are in the format FFF-SS where FFF is the fleet and SS is the sub-fleet. Type I systems are usually organized with different IDs assigned to different fleets. For example, a valid fleet/subfleet ID identifying all detectives within a police department might be 000-12, where 000 identifies all police IDs and 12 identifies the Detective division. To properly trunk a Type I system, you have to program the fleet map for the system.
Type II IDs are identified by a 5-digit number. Valid (programmable) Talk Group IDs are divisible by 16.
 
EDACS IDs come in two formats: AFS (Agency-Fleet-Subfleet) and Decimal.
 
AFS IDs are in the form AA-FFS where AA is the agency, FF is the fleet, and S is the sub-fleet. EDACS systems are organized with different IDs assigned to different fleets and agencies. For example, a valid agency/fleet/subfleet ID identifying all detectives within a police department in an agency might be 06-101, where 06 identifies the agency (Police), 10 identifies the Police division (East side), and 1 identifies the Detective division.
Decimal IDs are shown as a decimal number from 0 to 2047.
You can find a chart showing Decimal and AFS equivalents here: Conversion Chart.
 
LTR IDS are in the format A-HH-UUU where A is the area code (0 or 1), HH is the home repeater (01-20), and UUU is the user ID (000-254).

Receive Modes Contents
Each channel can have its own receive mode:
AM
, FM (NFM), CT (CTCSS), DC (DCS), MO (Motorola), ED (EDACS), or LT (LTR) mode.
If the receive mode of the channel is set to CT, PL codes appear in the format xxx.x, where xxx.x is a frequency in Hz.
If the receive mode of the channel is set to DC, DPL codes appear in the format xxx, where xxx is an octal code.
AM - Receives AM transmissions. MO - Receives Motorola IDs.
FM - Receives FM transmissions. ED - Receives EDACS IDs.
CT - Receives CTCSS tones. LT - Receives LTR IDs.
DC - Receives DPL (digital private line) tones.  

Understanding CTCSS/DCS  
Continuous Tone Coded Squelch System (CTCSS) and Digital Coded Squelch (DCS) are two methods used to prevent interference by other radio communications. Your scanner can receive transmissions that use these codes (or more commonly referred to as tones).

CTCSS and DCS systems all use some form of coded squelch. Coded squelch techniques involve the transmission of a special 'code' signal along with the audio of a radio transmission. A receiver with coded squelch only activates when the received signal has the correct 'code'. This lets many users share a single frequency, and decreases interference caused by distant transmitters on the same channel. In all major metropolitan areas of the United States, every available radio channel is assigned to more than one user. Public safety radio systems on the same frequency are usually set up at a distance of 40 miles apart, or more. This means that you may hear transmissions from a distant system when your local system is not transmitting. By programming the CTCSS tone for a local channel the scanner will not stop on transmissions from the distant system. With few exceptions, such as the VHF Aircraft and Marine bands, almost every other VHF or UHF radio system uses some form of coded squelch. By far, CTCSS is the most popular mode among non-trunked systems.

For more information visit Radio Reference's respective pages on CTCSS and DCS.

Open and Closed Modes  
Each channel bank can be set to open or closed mode.
In open mode the scanner will receive:

(1) all channels in AM, FM, CT, and DC modes, that are not locked out.
(2) all IDs in MO, ED and LTR modes, even if they are locked out in the ID list.

In closed mode the scanner will receive:

(1) all channels in AM, FM, CT, and DC modes, that are not locked out.
(2) only IDs in MO, ED, and LTR modes that are programmed into the ID list, and not locked out in the list.

In other words,
If you want to hear all IDs, scan in open mode. If you want to hear specific IDs, program them into the scan lists and scan in closed mode. If you want to hear specific IDs and not hear other IDs, program them into the scan lists, lock out the ones you don't want to hear, then scan in closed mode.

Keypad and Knob Controls Contents

Your scanner's keys might seem confusing at first, but this information should help you understand each key's function.
Key Function(s)
SCAN/ Scans the stored channels in scanning mode and enables Signal Stalker/Spectrum Sweeper.
FUNC(F) Lets you use various functions by pressing this key in combination with other keys.
MAN Stops scanning; lets you directly enter a channel number or frequency; steps to next channel in manual mode.
TRUNK(T) Automatically stores the trunking ID or holds the trunking ID while scanning.
WX/ (Weather) - Selects one of the pre-programmed weather channels.
PRI Turns the priority function on or off.
TEXT Lets you input text.
PSE (Pause) Stops searching or scanning.
MODE Changes the receive mode (AM, FM, MOT, ED, LT).
(Pro 97) Locks the keypad to prevent accidental program changes; turns on/off the display backlight.
DIM (Pro 2055) Adjusts the display brightness.
TUNE Allows you to tune to a frequency along with or .
ATT (Attenuate) Turns attenuation on to reduce the scanner's sensitivity and block extremely strong signals, or turns it off to increase sensitivity.
or Selects the scan or search direction; steps up or down through options during programming.
SRCH Selects one of the service searches or limit search.
L/OUT Locks/unlocks selected channels while scanning; locks/unlocks specified frequencies during a limit or service search.
PGM (PROG) Puts scanner in program mode; steps to next channel in program mode.
ENT Completes the entry of frequencies, IDs, and text.
CL (Clear) Clears an incorrect entry.
Number Keys Enter a channel or a frequency; turn groups on and off in search mode; select which banks to scan in scanning mode; enter numbers or characters for programming text.
(.) DELAY Enters a decimal point or space; programs delay time for the selected channel/search bank; hyphen in trunking ID programming.

Turning On The Scanner And Setting the Squelch  
1. Turn SQ fully counter-clockwise to min.
2. Turn VOLUME/OFF clockwise until it clicks and you hear a hissing sound.
3. Turn SQ clockwise until the hissing stops and then just a little more.
 
If you are using the scanner for the first time, straight out of the box, you should see all zeros in the frequency display. The scanner will not scan or trunktrack until you program frequencies into the banks. However, you can do a search and use the Signal Stalker.

A Look at the Display Contents
The display has indicators that show the scanner's current operating status. The display information helps you understand how your scanner operates.

In Scan Mode  
  1st Line
The banks that are selected for scanning will appear and the cursor will blink on the bank being scanned.
If there is a dot instead of the bank number, then the bank is not on for scanning.
pri--
will appear in the left if priority is off.
PRIon appears if priority is on monitoring an AM or FM channel.
PRIct appears if priority is on monitoring a channel in CT mode.
PRIdc appears if priority is on monitoring a channel in DC mode.
PRIwx appears if priority is on monitoring a weather channel.
 
  2nd Line
The + or - under the bank number will denote if the bank is open or closed. If there is a dot instead of the + or -, then the bank is not on for scanning.
atg appears when global attenuation is off for all channels/searches.
ATG appears when global attenuation is on for all channels/searches.
  3rd Line
Scanning up... or down... appears.
  4th Line
Displays the bank currently being scanned.
Low battery! blinks when the scanner's battery is low.

In Receive Mode  
  1st Line
ch will be appear in the left when the priority channel is receiving.
will be appear in the left when the scanner is in function mode.
M, P, S, or H appears in the top left showing manual, program, or scan modes. H appears when the scanner is receiving while holding on an ID.
000 appear as bank (0--) and channel number (-00) to the right of M, P, S or H then the receive mode.
0000.00000 shows the frequency.
The weather channel number in weather search.
  2nd Line
pri appears on the left with priority off. PRI appears with priority on.
att appears if the attenuator is off for the channel. ATT appears with the attenuator on for the channel.
atg appears when global attenuation is off for all channels/searches.
ATG appears when global attenuation is on for all channels/searches.
dly appears if the delay is off for the channel. DLY appears with the delay on for the channel.
lo appears if the channel is unlocked. LO appears if the channel is locked out; or VC if receiving an ID.
+ appears if the bank is open. - appears if the bank is closed.
A will appear to the right of the channel when the channel is receiving.
  3rd Line
Displays the channel name or Priority Channel if the priority channel is receiving.
  4th Line
If the receive mode of the channel is CT or DC the CT or DC code if programmed (with Search if in search mode) or
CT: or DC: Code Search
with no code received.
A will appear to the right of the tone if a tone is received.
If the receive mode of the channel is MO, ED, or LT The ID number (or tag) of the current ID.
In Manual mode on a Motorola control channel, the Motorola system ID and signal strength when not scrolling through the active IDs.
Low battery! blinks when the scanner's battery is low

In Search Mode Contents
  1st Line
SR0-SR6 will appear to show the current search band (or not for a TUNE search).
or will appear to show the search direction.
MO, ED, CT, DC, FM, or AM will appear in the top right to show the receive mode.
0000.00000 appears to the right to display the frequency.
  2nd Line
pri appears on the left with priority off. PRI appears with priority on.
att appears if the attenuation is off for the channel (SR0-2) or for the band (SR3-6).
ATT appears
if the attenuation is on for the channel (SR0-2) or for the band (SR3-6).
atg appears when global attenuation is off for all channels/searches. ATG appears when global attenuation is on for all channels/searches.
dly appears if the delay is off for the channel (SR0-2) or for the band (SR3-6).
DLY appears if the delay is on for the channel
(SR0-2) or for the band (SR3-6).
lo appears if the channel is unlocked (SR0-2). LO appears if the channel is locked out (SR0-2).
zm appears if zeromatic is off for the band. ZM appears if zeromatic is on for the band.
appears if the seek function is on.
  3rd Line
Channel -- SRCH  appears while searching channels in SR0-2.
Channel -- MAN appears when searching channels in SR0-2.
***PAUSED*** when paused on a channel or frequency.
Group 0123 will appear while searching the Police/Fire band the cursor will blink on the current search group. A . (dot) will replace the number if the group is turned off.
Group 012345 will appear while searching the Amateur band the cursor will blink on the current search group. A . (dot) will replace the number if the group is turned off.
  4th Line
The band name.
Fine Tune Mode in a TUNE search.
SKYWARN-1, 2, or 3 appears when viewing a Skywarn channel.
Low battery! blinks when the scanner's battery is low.

In Signal Stalker Mode Contents
  1st Line
Sig.Stalker or Sp.Stalker will appear to show which Signal Stalker mode is in use.
dly appears if the delay is off. DLY appears if the delay is on.
or will appear to show the stalk direction.
  2nd Line
att appears if the attenuation is off. ATT appears if the attenuation is on.
atg appears when global attenuation is off for all channels/searches. ATG appears when global attenuation is on for all channels/searches.
0000.00000 appears to the right to display the frequencies.
A will appear to the right of the frequency when receiving.
  3rd Line
Group 0123 will appear while stalking Police/Fire bands and the cursor will blink on the current search group. A . (dot) will replace the number if the group is turned off.
Group 0123456789 will appear while stalking All bands and the cursor will blink on the current search group. A . (dot) will replace the number if the group is turned off.
***PAUSED*** when paused on a channel or frequency.
  4th Line
The band name.
Low battery! blinks when the scanner's battery is low.

Programming Conventional Frequencies Contents
You can program trunking frequencies (1 trunking system per bank) and conventional frequencies into the same bank to utilize channel space better. That way, you don’t have to waste a whole bank on a trunking system that has only 5 channels. I typically put my trunking frequencies in starting at the beginning of the banks because you probably won't have more than 25 of those, and then fill up the banks with conventional frequencies.

Channels start at 000 for bank 0, 100 for bank 1, 200 for bank 2 etc.

If you are going to be programming text tags for the frequencies, I find it easier to program all the frequencies first, then go back and program all the text tags.
See also
Programming Trunking Systems.
Mode Frequency Range Step
(kHz)
AM 25-28 5
FM 28-54 5
AM 108-136.99166 8.33
FM 137-138 5
FM 138-144 12.5
FM 144-148 5
FM 148-150.775 12.5
FM 150.7825-150.8125 7.5
FM 150.815-154.4525 7.5
FM 154.45625-154.47875 7.5
FM 154.4825-154.505 7.5
FM 154.510-154.525 5
FM 154.5275-154.54625 6.25
FM 154.5475-154.6075 7.5
FM 154.610-154.655 5
FM 154.6575-156.2475 7.5
FM 156.250-157.475 5
FM 157.4775-161.565 7.5
FM 161.570-162.020 5
FM 162.025-173.200 12.5
FM 173.20375-173.2225 6.25
FM 173.225-173.3875 6.25
FM 173.390-173.40875 6.25
FM 173.4125-174 12.5
FM 216.0025-221.9975 5
FM 222-225 5
AM 225-406 25
FM 406-512 6.25
FM 806-823.9875 6.25
FM 849-868.9875 6.25
FM 894-960 6.25
FM 1240-1300 6.25
1. In Manual mode select the channel by entering the bank number and channel number (Ex: 000 for the first channel) then press MAN to advance to the channel.
You will see a M before the channel number to show manual mode.
  Note: You may also change banks by pressing FUNC then or (each time) and then change channels by pressing or .
2. Press PGM to put the scanner in program mode. You will see a P before the channel number to show program mode.
To Delete a frequency, press FUNC then CL.
To Delete all frequencies in the bank, press FUNC then 6.
3. Use the number keys and decimal point key to enter the frequency you want to store. If you make a mistake press CL to delete the last digit or press and hold CL to clear all the digits. Press ENT to store the frequency. The scanner will store the frequency in the default mode, AM or FM. If you want to change the receive mode to AM, FM, CT (PL), or DC (DPL), press MODE to change.
  Note: If you entered an invalid frequency (not in the receiver's range), Invalid Freq appears and the scanner beeps.
  Note: The scanner automatically rounds (down) the entered number to the nearest valid frequency. For example, if you key in 154.5175 (MHz), your scanner displays 154.515 when you press enter.
  Note: If you enter a duplicate frequency, Dupl. Freq. and the channel number of the previous frequency appear and the scanner beeps three times. Press ENT to accept or CL to clear.
  To Program the CTCSS or DCS tone, See Programming Tone Codes.
  To set the Delay for the channel, press DELAY to toggle the delay feature on or off.
  To set the Attenuation for the channel, press ATT to toggle the attenuator on or off.
  To Program Text for the Bank, see Text Tagging a Bank.
  To Program Text for the Channel, see Text Tagging a Channel.
4. Press PGM which advances to the next channel. The receive mode changes to the default mode (FM) while programming the channel but will store the correct mode after you hit enter to store it. Program the remaining channels the same way (step 3).
5. To Program any other channel, return to step 1.
To exit programming, press MAN.
 
Programming Tone Codes
You can set the receive mode of a (conventional) channel to receive any CTCSS or DCS tone code (if one is transmitted). You can also program a tone code for a channel (frequency) so the scanner will only stop on that channel if the programmed code is received with the frequency (regardless of open or closed modes).
 
To program a channel for CTCSS or DCS search:
1. In Manual mode, select the channel by entering the bank number and channel number then press MAN to advance to the channel.
  Note: You may also change banks by pressing FUNC then or (each time) and then change channels by pressing or .
2. Press MODE until you set the channel to CT Code Search or DC Code Search in the bottom of the display. Usually, but not always, VHF channels will use CTCSS and UHF channels will use DCS. If you leave the channel at this 'Search' setting, the scanner will display the first code (if) found when you do not program a code.
 
To program a CTCSS or DCS tone for a channel:
1. In Manual mode, select the channel by entering the bank number and channel number then press MAN to advance to the channel.
  Note: You may also change banks by pressing FUNC then or (each time) and then change channels by pressing or .
2. Press MODE until you set the channel to CT Code Search or DC Code Search in the bottom of the display.
3. Press PGM to put the scanner in program mode.
4. Press FUNC then MODE and you will see Set CTCSS Code or Set DCS Code in the top of the display. Use or to select the code then press ENT to store. The scanner will then only receive transmissions on that channel that use the programmed tone or code in scan mode.
Press MAN to exit programming.
 
In Scan Mode you can store the tone code of the frequency by pressing ENT while viewing the channel . Code Stored briefly appears in the display.
  Note: When stopped on an active conventional channel while scanning, you can press MODE to cycle through the valid modes for that channel, including CTCSS and DCS. This will reset any stored CT or DC code to the search code mode, allowing you to easily check for other CT or DC codes that may be present on the frequency.

Programming Trunking Systems Contents
You can program trunking frequencies and conventional frequencies into the same bank to utilize channel space better. That way, you don’t have to waste a whole bank on a trunking system that has only 5 channels. I typically put my trunking frequencies in (1 trunking system per bank) starting at the beginning of the banks because you probably won't have more than 25 of those, and then fill up the banks with conventional frequencies.

Channels start at 000 for bank 0, 100 for bank 1, 200 for bank 2 etc.
See also
Programming Conventional Frequencies.

Motorola frequencies can be programmed in any order. See also
Determining Base/Step/Offset for VHF/UHF Motorola Systems.

EDACS frequencies have to start at 001, 101, 201, etc. and have to be programmed in LCN (Logical Channel Number) order. You can still use 000, 100, etc. for a conventional frequency.

LTR frequencies also have to be programmed in LCN (Logical Channel Number) order to properly track the system. See also Repeater Finder Tool.
 
Valid Trunking Frequencies: Note: These scanners will not trunktrack VHF systems.
Motorola Type II-IIi Systems: Motorola Type I Systems: Ericsson EDACS Systems: LTR Systems:
406-512 MHz 806-900 MHz (except cell freqs) 406-512 MHz 406-512 MHz
851-869 MHz (except cell freqs)   806-900 MHz (except cell freqs) 806-900 MHz (except cell freqs)
935-940 MHz   900-956 MHz 900-956 MHz
 
1. In Manual mode select the channel by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
  Note: You may also change banks by pressing FUNC then or (each time) and then change channels by pressing or .
  Note for EDACS programming: EDACS frequencies have to start in the second channel of the bank (channels 001,101, 201, etc.), and have to be programmed in LCN (Logical Channel Number) order. See Finding EDACS LCN Order. You can still use 000, 100, etc. for a conventional frequency.
  Note for LTR programming: LTR frequencies have to be programmed in LCN (Logical Channel Number) order also.
See also using the Repeater Finder Tool.
2. Press PGM then TRUNK to put the scanner in program and trunk modes.
3. Press MODE until the desired mode, MOT: none (for Motorola systems), ED: none (for EDACS systems) or LTR:none (for LTR systems) appears in the display. This sets the talk group ID decoding method for the bank.
4. (Motorola 800 systems only) Press FUNC then 3 to select the base frequency. Press or to select NORMAL or SPLINTER then press ENT to save and return.
  Note: Apparently, the default setting of 'Normal' works for most systems. 'SPLINTER' is for systems with splinter channels (analog 800Mhz  systems with frequencies between 866-869 MHz [or rebanded 851-854 MHz] ending with 0 instead of 5 e.g. 852.1250, not 852.1375). If, after programming, the system won't receive properly, try changing the setting (steps 1-4).
5. Press PGM. You should see the channel number in the top of the display and a P before the channel number to show program mode.
6. Use the number keys and decimal point key to enter the frequency you want to store. If you make a mistake press CL to delete the last digit or press and hold CL to clear all the digits. Press ENT to store the frequency.
  Notes: If you entered an invalid frequency (not in the receiver's range), Invalid Freq appears and the scanner beeps. The scanner automatically rounds (down) the entered number to the nearest valid frequency. For example, if you key in 154.5175 (MHz), your scanner displays 154.515 when you press enter.  If you enter a duplicate frequency, Dupl. f and the channel number of the previous frequency appear and the scanner beeps three times. Press CL to clear or ENT to accept.
 
7. Press MODE until the desired mode, MOT: none (for Motorola systems), ED: none (for EDACS systems) or LTR:none (for LTR systems) appears in the display. This sets the talk group ID decoding method for the channel. This will also stay as default while you are programming the rest of the trunking frequencies.
  To set the Attenuation for the channel, press ATT to toggle the attenuator on or off.
  To Program Text for the Bank, see Text Tagging a Bank.
  To Program Text for the Channel, see Text Tagging a Channel.
8. Press PGM to advance to the next channel. Use the number keys and decimal point key to enter the next frequency and press ENT to store. Enter the remaining frequencies the same way.
Press MAN exit programming.
To Program IDs into the scan lists see Programming Talk Group IDs.
If you Programmed a Motorola Type I or Type IIi system see Programming a Fleet Map.
If you Programmed a Motorola UHF system see Programming Offset and Base Frequency.

Programming a Fleet Map Contents
Motorola Type I or Type IIi systems require you to program a fleet map. This allows you to receive the talkgroup IDs correctly. If you don’t know which fleet map to use, you can try a method I found at Radio Reference.com.. Since it is rather lengthy, I will just give you the link. Determining Type I Motorola Fleet Maps by Dave Goodson. If you know the fleet map by name, E1P1, E1P2, etc., I have listed 16 pre-set fleet maps so you can see the size codes.
 
1. In Manual mode select any channel in the bank you want to program the fleet map in (Ex: 001) then press MAN to advance to the channel.
2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the ID list and MOT: none.
 
3. Press FUNC then 8. SizeCode Setting Use Code 15 for Type II Blocks Block 0 SC=00 will appear.
4. Enter the size code for block 0 (ex:8 for S-8). If you make a mistake, press CL to clear the entry.
5. Press ENT to store the size code for the first block and move to the next block. Program the rest of the block codes the same way. The ID list will re-appear after you program the last block.
  Note: If you select size code S-12, S-13, or S-14, these restrictions apply:
  S-12 can only be assigned to Blocks 0, 2, 4 or 6.
  S-13 can only be assigned to Blocks 0 and 4.
  S-14 can only be assigned to Block 0.
  Since these size codes require multiple blocks, you will be prompted for the next available block. For example, if you assign Block 0 as S-12, the scanner prompts you for block 2, the next block available, instead of block 1. If you assign Block 0 as S-14, you would not see another prompt because S-14 uses all available blocks.
Press MAN to exit programming.

Preset Fleet Maps Contents
In Motorola II systems (no programming the fleet map required), all the blocks have size code, S0, which has a size limitation of 512 radios. In Type I systems, size codes are used in different blocks to denote the maximum number of users in that block. Notice that size code S-12 uses 2 blocks. A Motorola Hybrid system (Type IIi) has 'blocks' of the system that are Type I Fleets/Subfleets and Type II talkgroups. The maps that are Hybrid systems are in bold.
E1P1 E1P2 E1P3 E1P4 E1P5 E1P6 E1P7 E1P8
Block Size Code Block Size Code Block Size Code Block Size Code Block Size Code Block Size Code Block Size Code Block Size Code
0 S-11 0 S-4 0 S-4 0 S-12 0 S-4 0 S-3 0 S-10 0 S-1
1 S-11 1 S-4 1 S-4 1 (S-12) 1 S-4 1 S-4 1 S-10 1 S-1
2 S-11 2 S-4 2 S-4 2 S-4 2 S-12 2 S-4 2 S-11 2 S-2
3 S-11 3 S-4 3 S-4 3 S-4 3 (S-12) 3 S-4 3 S-4 3 S-2
4 S-11 4 S-4 4 S-4 4 S-4 4 S-4 4 S-12 4 S-4 4 S-3
5 S-11 5 S-4 5 S-4 5 S-4 5 S-4 5 (S-12) 5 S-4 5 S-3
6 S-11 6 S-4 6 S-12 6 S-4 6 S-4 6 S-12 6 S-4 6 S-4
7 S-11 7 S-4 7 (S-12) 7 S-4 7 S-4 7 (S-12) 7 S-4 7 S-4
 
E1P9 E1P10 E1P11 E1P12 E1P13 E1P14 E1P15 E1P16
Block Size Code Block Size Code Block Size Code Block Size Code Block Size Code Block Size Code Block Size Code Block Size Code
0 S-4 0 S-0 0 S-4 0 S-0 0 S-3 0 S-4 0 S-4 0 S-3
1 S-4 1 S-0 1 S-0 1 S-0 1 S-3 1 S-3 1 S-4 1 S-10
2 S-0 2 S-0 2 S-0 2 S-0 2 S-11 2 S-10 2 S-4 2 S-10
3 S-0 3 S-0 3 S-0 3 S-0 3 S-4 3 S-4 3 S-11 3 S-11
4 S-0 4 S-0 4 S-0 4 S-0 4 S-4 4 S-4 4 S-11 4 S-0
5 S-0 5 S-0 5 S-0 5 S-0 5 S-0 5 S-4 5 S-0 5 S-0
6 S-0 6 S-4 6 S-0 6 S-0 6 S-0 6 S-12 6 S-12 6 S-12
7 S-0 7 S-4 7 S-0 7 S-4 7 S-0 7 (S-12) 7 (S-12) 7 (S-12)
 
Size Code Fleets Sub Fleets Number of Blocks Number of Talkgroups per Block Max IDs per Talkgroup Max Radios per Block
S0 N/A N/A N/A N/A N/A 512?
S1 128 4 1 512 16 16
S2 16 8 1 128 64 64
S3 8 8 1 64 128 128
S4 1 16 1 16 512 512
S5 64 4 1 256 32 32
S6 32 8 1 256 32 32
S7 32 4 1 128 64 64
S8 16 4 1 64 128 128
S9 8 4 1 32 256 256
S10 4 8 1 32 256 256
S11 2 16 1 32 256 256
S12 1 16 2 8 1024 512
S13 1 16 4 4 2048 512
S14 1 16 8 2 4096 512
 
You can tell which block a Motorola ID is in by its number.
Block Lower ID# Upper ID#
0 0000 8191
1 8192 16383
2 16384 24575
3 24576 32767
4 32768 40959
5 40960 49151
6 49152 57343
7 57344 65535

Thanks to
Radio Reference.com for most of this information.

Programming the Offset and Base Frequency  
To properly track Motorola UHF-lo (406-512 MHz) trunked systems, you must program the applicable offset and base frequency for each system. This can be done after you program the trunking frequencies and system. If you don't know the offset and base frequency, I have found an explanation at the Trunked Radio Systems User’s Page. Look for 'Determining Base and Offset Frequencies for the BC245xlt' by John C. There is a similar explanation at Radio Reference.
 
1. In Manual mode select any channel in the bank containing the UHF system by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the ID list.
3. Press MODE. MOT: none should appear in the display.
4. Press FUNC then 2. You will see the current settings for the base frequency, offset, and step size. While B in Base is blinking, enter the base frequency then press ENT. Press ENT again to confirm and move down to the Offset setting. Or, if the entry is correct, press ENT to move down.
5. While O in Offset is blinking, enter the offset then press ENT. Press ENT again to confirm and move down to the Step setting. Or, if the entry is correct, press ENT to move down.
6. While S in Step is blinking, press or to select the step then press ENT to confirm and exit. Or, if the entry is correct, press ENT to exit.
Press MAN to exit programming or SCAN to start scanning.

Programming Talk Group IDs Contents
After you program trunked frequencies into a bank, your scanner has 5 scan lists for each bank where you can store IDs. Each list can contain up to 30 IDs, for a total of 150 IDs for each trunk scanning bank. Each of the 5 lists can be turned on or off. If you use all the banks as trunking banks, you can store up to 1500 IDs. If you have more than 150 IDs for a system, or want another list and have an extra bank in your scanner, program the trunked system into 2 banks. You could then have 10 lists (up to 300 IDs) to store and turn on or off for that system.

If you are going to be programming text tags for the IDs, I find it easier to program all the IDs first, then go back and program all the text tags.

To Automatically Store an ID into the first available ID location while trunking, quickly press TRUNK. ID saved briefly appears at the bottom of the display. The ID list (0-4) and ID# (0-29) will briefly be displayed on the bottom line. ID was saved briefly appears at the bottom of the display if the ID has previously been stored (or programmed). If you try to enter more than 150 IDs in a bank, Memory Full! appears.

To Manually Store an ID:
  1. In Manual mode select any channel in the bank containing the ID by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
  2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the bank number (0-9), list number (0-4), and the list status (ON or OFF) on the top line.
  3. Press Mode (each time) to select the correct trunking mode if needed.
  4. Press TRUNK (each time) to select one of the 5 ID lists (0-4).
  5. Select the ID# (0-29) by pressing or (or press and hold; faster).
  To Enter an ID:
  To enter a Motorola Type II ID, enter the ID then press ENT to store the ID.
  To enter a Motorola Type I ID, enter the fleet# then press the decimal point to enter a hyphen, then enter the sub-fleet#. Press ENT to store the ID.
  To enter an EDACS ID in decimal (the default) format, enter the ID then press ENT to store the ID. (You don't have to enter leading zeros).
  To enter an EDACS ID in AFS format, press FUNC then 2 to change to AFS format. AFS format will briefly appear on the bottom line. Enter the agency number (xx), use the decimal key for a hyphen, enter the fleet and sub-fleet (xxx), then press ENT to store the ID. See also Switching EDACS Format Display.
  To enter a LTR ID, enter the ID (no hyphens) then press ENT to store the ID.
  Note: If you enter a duplicate ID, Dupl ID and the list number and location of the ID will appear. Press CL to clear or ENT to accept.
  Note: If you enter the ID in the wrong format (ex: an EDACS ID into a Motorola bank), the scanner will beep 3 times and Invalid ID will appear briefly on the bottom line.
  To Text Tag An ID, press TEXT. Move the cursor to the position you want using to move right, or to move left, then skip to Entering Characters.
  To Set the ID Delay for the Bank, Press FUNC then DELAY. Press or to select the delay then press ENT to store the setting. You can't set ID delays per ID like channels. See Changing ID Delay.
  To Lock or Unlock an ID, press L/OUT. LO will appear in the display to the right of the ID# if it is locked out and lo will appear if it is unlocked.
  Press to move to the next ID location and enter the rest of the IDs the same way.
Press MAN to exit programming or SCAN to start scanning.

Changing ID Delay
You have to set the ID delay for the bank to pause on an ID before scanning resumes. Setting the scan delay for the channel has no effect on an ID. The delay can only be set for the whole bank, not an individual ID. When activated, the ID delay watches the control channel command for the delay time when the signal disappears from the voice channel.
 
1. In Manual mode select any channel of the bank you want to turn a list on or off in by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the ID list.
3. Press FUNC then DELAY. Use Up/Down keys to set ID delay appears in the display.
4. Press or to change the delay then press ENT to store the setting.
Press MAN to exit programming.

Clearing IDs
To Clear a Single ID:
  1. In Manual mode select any channel of the bank that has the ID you want to clear by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
  2. Press PGM the TRUNK. You will see the bank number (0-9), list number (0-4), and the list status (ON or OFF) on the top line.
  3. Press TRUNK (each time) to select the list (0-4). Select the ID# (0-29) by pressing or (or press and hold; faster).
  4. Press FUNC then CL. Press MAN to exit programming or SCAN to start scanning.
To Clear All IDs in a Bank:
  1. In Manual mode select any channel of the bank you want clear the IDs in by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
  2. Press PGM the TRUNK. You will see the bank number (0-9), list number (0-4), and the list status (ON or OFF) on the top line.
  3. Press FUNC then 6. Clear entire list ? Press 1 to clear all, any other key aborts appears. Press 1 and Please wait (if there are a lot of IDs) then List cleared will appear. Then the ID list will re-appear. Press MAN to exit programming or SCAN to start scanning.

Signal Stalker II Contents
Your scanner's Signal Stalker II feature provides a powerful new tool for you to rapidly detect, monitor, and store frequencies from nearby radio transmissions. The Signal Stalker II feature is more sensitive than portable frequency counters and will detect transmissions at a greater distance. Signal Stalker II functions by rapidly sweeping through the RF spectrum in 1 MHz segments. If RF signal energy is detected in a 1 MHz segment, Signal Stalker II will sweep through the 1MHz segment in finer steps until the source of the RF signal energy is found. The Signal Stalker II feature is similar in functionality to portable frequency counters that cost much more than your scanner, but provides many advantages over typical portable frequency counters. For example: The Signal Stalker II allows you to sweep the entire range of your scanner's design frequencies, or you can specify just those frequency ranges that you wish to sweep.

The Signal Stalker II feature can be set to watch for activity on all band frequencies or Police/Fire frequencies only. You can turn on/off frequency sub-bands (groups). You can activate the
Attenuator and/or turn the Delay on also. You can lock out 150 frequencies while searching all bands and 50 frequencies while searching Police/Fire frequencies.

Special Signal Stalker

You can also change the Normal Signal Stalker II operation to the Special Signal Stalker II operation. In the Special Stalker operation, the frequency range is still divided by 1 MHz segments. But, if you lockout 5 frequencies within a 1 MHz segment, the scanner will skip that entire segment in subsequent sweeps.

Certain segments of the spectrum are used by high power transmitters, such as paging transmitters. You can press L/OUT when the Signal Stalker II stops on these undesired transmissions to prevent the Signal Stalker II from stopping on them in future sweeps, however, the Signal Stalker II will still see their signal energy when sweeping through the 1 MHz segment. This will cause the Signal Stalker II to execute another fine step search of the 1 MHz segment. If you have locked out the undesired transmissions, the Signal Stalker II will not stop on them again but the overall sweep performance of the Signal Stalker II will be slowed accordingly.
  Note: Priority mode is not available while using Signal Stalker II.
 
Signal Stalker searches in 2 modes:
All bands and just Police/Fire bands.
 
All Signal Stalker bands
Band 0 25-54
Band 1 108-137
Band 2 137-174
Band 3 216-300
Band 4 300-406
Band 5 406-470
Band 6 470-512
Band 7 806-869
Band 8 894-960
Band 9 1240-1300
Police/Fire Signal Stalker bands
Band 0 33.4-46.5
Band 1 151-170
Band 2 453-467
Band 3 851-869
 
To Turn Signal Stalker ll On, Press and hold (SCAN). Sig.Stalker and the group numbers will appear in the display. The cursor will blink on the group being stalked.
 
  To switch between All groups and Police/Fire groups, Press FUNC then (SCAN). Rx: All Bands or Rx: Police/Fire will appear in the bottom of the display.
  To switch between Normal Signal Stalker and Special Signal Stalker, Press FUNC then or . Sp.Stalker appears in the top of the display when Special Signal Stalker is on.
  To turn band groups on or off, press the number keys (0-9).
  To change search directions or resume stalking, press the or button. An arrow in the upper right of the display shows the direction.
  To Pause on a frequency, quickly press PSE to stop searching and listen to the transmission. **PAUSED** appears in the display. To continue searching, press PSE again.
  To Lock out a frequency, quickly press L/OUT while the frequency is displayed.
  To Review or Unlock frequencies, press FUNC then L/OUT and you will see the first locked frequency, the group (gx), and the 1 MHz segment (xxx)(?), and L/Out xxx of xxx in the display. Press to step through the locked out frequencies. To unlock a frequency, press CL. Press FUNC then L/OUT to exit.
  To Clear All locked out frequencies in All groups, press FUNC then L/OUT and you will see the lockout list. Press FUNC then 6. Clear entire list? Press 1 to clear all, any other key aborts appears in the display. Press 1 to unlock all frequencies. List cleared briefly appears in the display then No Lockout. Press FUNC then L/OUT to exit.
  Note: You will have to turn the Delay and/or Attenuator back on after clearing the list(??).
  To turn the Attenuator on or off for all groups, press ATT.
  To turn the Delay on or off for all groups, press DELAY.
  To Copy a frequency into a channel, quickly press FUNC then PGM. Then see Frequency Copy.
  To Copy a frequency into the priority channel, quickly press FUNC then PRI while the channel is displayed. The display will flash twice and the frequency will be copied into the priority channel.
To exit, press (SCAN) or MAN.

Scanning Conventional Banks Contents
 
The scanner won't scan unless frequencies are first programmed into the channels. See Programming Conventional Frequencies.
 
Press SCAN to start scanning.
Select any combination of banks to scan by pushing the number keys that correspond to the banks. Numbers appear at the top of the display showing the currently selected banks. Banks that show . (dots), are turned off. The scanner scans through all the channels in the bank and moves to the next bank. The cursor blinks on the bank number when the scanner scans the channels in that bank. If the scanner finds an active channel, it stops on it. When the transmission ends, the scanner resumes scanning. If it is a long transmission, (such as a Ham rag chewing) and you want to move on, press SCAN again to resume scanning. The scanner won't scan channels that are locked out or have 0 as the frequency.
  If the scanner picks up an unwanted partial frequency, turn SQ clockwise to decrease the scanner's sensitivity and mute the scanner so it will continue scanning.
  To listen to a weak or distant frequency, turn SQ counter-clockwise to increase the scanner's sensitivity.
  To change the scan direction, press or .
  To turn banks on or off while scanning, press the number key, 0-9 that corresponds with bank you want to turn on or off. You cannot turn off all banks. One bank must always be active.
  To Pause on a channel, quickly press MAN while the channel is displayed. Press SCAN to resume.
  To Lock out a channel, quickly press L/OUT while the channel is displayed. See Locking-out Channels.
  To turn the Delay on or off for a channel, quickly press DELAY while the channel is displayed.
  To Attenuate a channel, quickly press ATT while the channel is displayed.
  To Store the CTCSS or DCS tone, quickly press ENT while the tone is displayed. Code Stored briefly appears in the display. See Programming Tone Codes.
  To change the Receive Mode of a channel, quickly press MODE while the channel is displayed.
  To set a channel as the Priority Channel, quickly press FUNC then PRI while the channel is displayed. See Priority Scanning.
To exit scanning, press MAN.

Changing Receive Modes
The scanner is preset to the most common AM or FM receive mode for each frequency range. The preset mode is correct in most cases. However, some amateur radio transmissions and trunked systems do not operate in the preset mode. If you try to listen to a transmission when the scanner is not set to the correct receive mode, the transmission might sound weak or distorted. See also Understanding CTCSS/DCS.
 
To change the Receive Mode of a channel, select the channel in manual mode by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel. Press MODE until the desired mode is found.
  Note: You cannot change the receive mode of a non-trunked channel to MO, ED or LT.
Or, if the scanner is scanning and stops on an active channel, quickly press MODE to change the mode.

Using the Attenuator Contents
To reduce interference or noise caused by strong signals, you can reduce the scanner's sensitivity to these signals. There are two attenuator modes in your scanner. One is normal attenuator mode in which you set the attenuator for each channel (and channels in search SR0-2), each search group (in search banks SR3 and SR5), each search band (SR4 and SR6), or a Tune search. The other is global mode in which applies global attenuation (on or off) to every channel or search regardless of the channel or search attenuation setting.
 

To turn the Attenuator on or off for a single channel while scanning, quickly press ATT while the channel is displayed or select the channel in manual mode by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel. Press ATT. att turns to ATT in the display when the channel is attenuated.
To turn the Attenuator on or off for Search, press ATT during the search. att turns to ATT in the display when the search is attenuated.
To toggle the Global Attenuator Mode on or off, while searching or scanning, press FUNC then ATT.
To toggle Global Attenuation on or Global Attenuation off, Press ATT while Global Attenuator Mode is active.
ATG
appears in the display when global attenuation is on for all channels/searches.
atg
appears in the display when global attenuation is off for all channels/searches.

Attenuation Settings

   

Attenuation

Global Mode

Display

Results

Off

Off

att

Channel/search attenuation Off

On

Off

ATT

Channel/search attenuation On

On or Off

Off

atg

Attenuation Off- all channels/searches

On or Off

On

ATG

Attenuation On- all channels/searches

Priority Scanning  
You can program one additional conventional frequency, a stored conventional channel, or a weather channel as a priority channel. The Priority feature lets you scan through the channels and still not miss important or interesting calls on a specific frequency. When a channel is selected as the priority channel and priority is turned on, the scanner checks that channel or frequency every 2 seconds, and stays on the channel if there is activity until the activity stops even if the bank for the channel is turned off. The priority feature also works in Search and Manual modes.

The Priority feature does not work properly while trunking an EDACS or Motorola system. (It may seem to work at first but will jump off IDs when the feature checks the priority channel while receiving certain trunked transmissions, especially EDACS, if you can tolerate that. Or, it will not check the priority channel at all during some trunked transmissions).

To Program a channel as the priority channel in manual mode, enter the bank number and channel number then press MAN to advance to the channel. Press FUNC then PRI. You will see Priority Channel blink twice on the bottom line.
  Note: You cannot program a channel which has a receive mode of MO or ED as the priority channel.
To Program a channel when the scanner is scanning and stops on an active channel, quickly press FUNC then PRI before it continues scanning again. You will see Priority Channel blink twice on the bottom line.
To Program a frequency as the priority channel, in manual mode, press PGM then PRI. Enter the frequency you want to use as the priority channel then press ENT.
To Program a Weather Channel as the priority channel, press WX. Select the weather channel you want to use as the priority channel then press FUNC and PRI. You will see Priority Channel blink twice on the bottom line. Press MAN or SCAN to exit. If you program a weather channel as the priority channel, the scanner goes to the priority channel only when the scanner detects the weather alert tone. See Receiving SAME Weather Alerts.
To turn on the Priority Feature, press PRI. When the priority channel is active, Pch will appear on the top line to the left of the channel or frequency.
  PRIon appears in the top line if a AM or FM channel is programmed as the priority channel.
  PRIct appears in the top line if a channel in CT mode is programmed as the priority channel.
  PRIdc appears in the top line if a channel in DC mode is programmed as the priority channel.
  PRIwx appears in the top line if a weather channel is programmed as the priority channel.
To turn off the Priority Feature, press PRI.

Locking/Unlocking Channels  
You can keep the scanner scanning by locking out channels that have a continuous transmission (such as a weather channel).
 
To Lock or Unlock a channel, select the channel by entering the bank number and channel number (Ex: 001) then press MANUAL to advance to the channel. Press L/OUT. lo changes to LO in the display if the channel is locked out.
To Lock out a Channel if the scanner is scanning and stops on the channel, quickly press L/OUT before it continues scanning again. The scanner will lock out the channel and automatically resume scanning.
To View all locked out channels, in manual or program mode, press FUNC then L/OUT (each time) to step through the locked out channels. Press L/OUT to unlock a channel. If there are no locked out channels, then the scanner will just beep.
  Note: You can still monitor locked out channels in manual and program modes.

Scanning and Trunking Banks Contents
You can trunktrack a selected bank only after you have programmed the frequencies and trunking system for that bank. See Programming Trunked Systems.
 
Your scanner automatically mutes the audio during trunking when it decodes control channel data. However, it is recommended that (in manual mode) you turn SQ clockwise and leave it set to a point just after the hissing sound stops. This lets the scanner quickly acquire the data channel.
 
If you have a trunk system programmed (correctly) into a bank with conventional frequencies, the scanner will scan and trunktrack. You can't make it only scan or only trunktrack the bank (unless you lock out those frequencies you don't want scanned or trunktracked).
 
Press SCAN to start scanning.
Select any combination of banks to scan by pushing the number keys that correspond to the banks. Numbers appear at the top of the display showing the currently selected banks. The cursor blinks on the bank number when the scanner scans the channels in that bank. If the scanner finds an active channel or ID, it stops on it. When the transmission ends, the scanner resumes scanning. If it is a long transmission, (such as a Ham rag chewing) and you want to move on, press SCAN again to resume scanning. The scanner won't scan channels that are locked out or have 0 as the frequency.
  If the scanner picks up an unwanted partial frequency, turn SQ clockwise to decrease the scanner's sensitivity and mute the scanner so it will continue scanning.
  To listen to a weak or distant frequency, turn SQ counter-clockwise to increase the scanner's sensitivity.
  To change the scan direction, press or .
  To turn banks on or off, press the number key, 0-9 that corresponds to the bank you want to turn on or off. You cannot turn off all banks. One bank must always be active.
  To Open or Close a bank, quickly press FUNC then DELAY while any channel in the bank is displayed or when the cursor blinks on the bank number. See Changing Open and Closed Modes.
  To Pause on a Conventional channel, quickly press MAN while the channel is displayed. Press SCAN to resume.
  To Pause on a Trunked ID, quickly press and hold TRUNK while the ID is displayed. ID hold mode appears in the display and an H will appear to the left of the channel number while receiving. To resume scanning press SCAN.
  To Pause on a selected ID, press PGM then TRUNK. Press TRUNK (each time) to select one of the 5 ID lists. Press or to locate the ID and press FUNC then TRUNK. ID hold mode appears in the display and the ID# will appear at the bottom. To resume scanning press SCAN.
  To Store an ID into the first available ID location, quickly press TRUNK while the ID is displayed. The ID list (0-4) and location in the bank (0-29) will briefly be displayed on the bottom line. If the ID has previously been stored (or programmed), ID was saved will briefly appear. See Programming Talk Group IDs.
  To Lock out a conventional channel, quickly press L/OUT while the channel is displayed. If you lock out a trunking channel, the trunking system may not trunktrack properly. See Locking-out Channels.
  To Lock out an ID, L/OUT while the ID is displayed. See Locking/Unlocking IDs.
  Note: You cannot lockout an ID in 'pause' mode.
  To turn the Delay on or off for a conventional channel, quickly press DELAY while the channel is displayed.
  To turn the Delay on or off for a trunking system, see Changing ID Delay.
  To Attenuate a channel, quickly press ATT while the channel is displayed.
  To Store the CTCSS or DCS tone for a conventional channel, quickly press ENT while the tone is displayed. Code Stored briefly appears in the display. See Programming Tone Codes.
  To change the Receive Mode of a channel, quickly press MODE while the channel is displayed. If you change the mode of a trunking channel, the trunking system will not trunktrack properly.
  To turn on the Priority Feature, press PRI.
  To set a conventional channel as the Priority Channel, quickly press FUNC then PRI while the channel is displayed. See Priority Scanning.
  To View the ID or Text Tag for the ID, quickly press TEXT while any ID in the bank is displayed. Press TEXT again while any ID in the bank is displayed to revert.
  To turn ID lists on or off (in closed mode only), quickly press FUNC then TRUNK while an ID is displayed. 'ID Banks:' and the lists that are turned on will appear as numbers on the 3rd line when transmissions are received. The cursor will blink on the list number that has the receiving ID. If the list is turned off a . (dot) will replace the number. Quickly press FUNC then the list number while receiving to turn the list on or off. (Yeah, right, real simple). Quickly press FUNC then TRUNK while an ID is displayed to get rid of the 'ID Banks:' selection line.
Or, See Turning ID Lists Off and On to do it in Manual mode before scanning.
To exit trunking and scanning, press MAN.
 
While trunking, you may not know which agency, fleet, or talk group the talk group IDs are assigned to until you listen a while. You can determine the type of agency you are listening to after a short while by matching the IDs with the transmission you hear. You can then program them into ID lists. See Programming Talk Group IDs. Determining the service associated with a talk group ID might take awhile but finding IDs is half the fun.

Changing Open and Closed Modes Contents
You can set each bank to open or closed mode.
 
In open mode the scanner will receive:
(1)
all channels in AM, FM, CT and DC modes that are not locked out.
(2) all IDs in MO and ED modes, even if they are locked out in the ID list.
In closed mode the scanner will receive:
(1)
all channels in AM, FM, CT and DC modes, that are not locked out.
(2) only IDs in MO, ED, and LT modes that are programmed into the ID list, and not locked out in the ID list
 
In Manual mode select any channel of the bank you want to open or close by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
Press FUNC then DELAY to toggle between open and closed modes.
Or, while scanning, quickly press FUNC then DELAY while any channel or ID in the bank is displayed or when the cursor blinks on the bank number.

Turning ID Lists Off and On (In Closed Mode only)
Before Scanning
1. In Manual mode select any channel of the bank you want to turn a list on or off in by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the bank number (0-9), list number (0-4), and the list status (ON or OFF) on the 1st line, the ID# in the list (0-29) on the 2nd line, the ID on the 3rd line, and bank tag on the 4th line (if programmed).
3. Press TRUNK (each time) to select one of the ID lists (0-4) to turn on or off.

4. Press FUNC then 1 to turn the list on or off. Press SCAN or MANUAL to exit.

During Scan in Closed Mode (More practical for just turning lists off)  
1. Press FUNC then TRUNK while any ID in the selected bank is displayed to bring up the 'ID Banks:' list. The cursor will blink on the list number that has the receiving ID.
2. Press FUNC then list number (0-4) while any ID in the selected bank is displayed to turn the list on or off.
Note: You will have to wait to receive an ID in a list that is turned on to see the 'ID Banks:' list to turn a list on that is off. Quickly press FUNC then TRUNK while an ID is displayed to get rid of the 'ID Banks:' line (and see the ID tag again).

Locking/Unlocking IDs Contents
You can lock out IDs you don't want to hear such as telemetry, MDT's, dog catcher, etc.
 
To Lock out an ID while scanning, quickly press L/OUT while the ID is displayed.
To Lock or Unlock an ID manually:
  1. In Manual mode select any channel of the bank you want to lock or unlock an ID in by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
  2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the bank number (0-9), list number (0-4), and the list status (ON or OFF) on the 1st line, the ID# in the list (0-29) on the 2nd line, the ID on the 3rd line, and bank tag on the 4th line (if programmed).
  3. Press TRUNK (each time) to select the ID list (0-4).
  4. Select the ID# (0-29) by pressing or (or press and hold; faster) then press L/OUT to lock or unlock the ID. An L will appear to the right of the ID# if the ID is locked out.
  5. Press MAN to exit programming.
To Unlock IDs in a bank:
  1. In Manual mode select any channel of the bank you want to view the locked out IDs in by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
  2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the ID list.
  3. Press FUNC then L/OUT (each time) to view the locked IDs. Press L/OUT to unlock the ID. The next locked out ID will appear.
  4. Press MAN to exit programming.
  Note: You cannot unlock all IDs at one time.

Switching Text and ID Code Display
You can switch between displaying the ID code or the text you have programmed for the IDs.
 
To View the ID or the Text Tag for the IDs, while scanning, quickly press TEXT while any ID is displayed. Press TEXT again while any ID is displayed to change back.

Switching EDACS Format Display
The EDACS system uses two group ID formats. Decimal, and Agency-Fleet-Subfleet (AFS). Decimal IDs appear as 3 or 4 digit numbers, 577 (for example). AFS format IDs appear as 10- 047 (for example). Decimal is the default format. If you have your list of IDs shown in one format and the ID you want to receive in the bank is in the other format, you can switch.
 
1. In Manual mode select any channel of the bank you want to change the format in by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the ID list.
3. Press FUNC then 2. AFS format will briefly appear on the bottom line (if the default decimal display is on). To switch back, press FUNC then 2 again. Decimal form will appear in the display.
Press MAN to exit programming.

Searching for Frequencies Contents
With a service bank search, you can search for CB, Marine, Police/Fire, Aircraft, or Amateur transmissions without knowing the specific frequencies used in your area. The scanner is pre-programmed with most of the frequencies allocated to these services.
Or, you can program the Limit search to search within any lower and upper frequency.
Or, you can search up or down from a specific frequency using the Tune feature.

Marine, CB, or FRS/GRMS/MURS Search  
The CB, Marine, and FRS/GMRS/MURS bands are actually frequencies pre-programmed into special channels. You are not searching from a lower frequency to a higher frequency.
 
To start a Marine(SR0), CB(SR1), or FRS(SR2) search, press search until SR0 (for Marine) or SR1 (for CB) or SR2 (for FRS) appears in the top left of the display. Press FUNC then SRCH to start searching. The channel numbers and search band name will appear in the display. Pressing FUNC and SRCH again will stop the search.
  Note: if you exit the CB(SR1) or FRS(SR2) search without stopping the search, the scanner will start searching automatically the next time you return to the band until you press FUNC then SRCH while in the band to stop searching. You must press FUNC then SRCH each time you enter the SR0 (Marine) to start searching.
  To change search directions or continue searching, press the or button. An arrow in the upper left of the display shows the direction.
  To turn the Seek function on or off, press FUNC then 7 while searching. Seek ON or OFF will briefly appear on the bottom line. will appear in the right of the display when the 'Seek' feature is on.
  To Pause on a channel, quickly press PSE to stop searching. **PAUSED** appears in the display. To resume searching, press PSE again.
  To Step through the channels one at a time, press PSE to stop searching then press the or button to step through the channels. You can also directly enter the channel number (01-40). To resume searching, press PSE again.
Or, to see the channel numbers,
press FUNC then SRCH to stop the search. Press the or button to step through the channels. Again, you can directly enter the channel number (01-40). To resume searching, press FUNC then SRCH again.
  To Lock out a channel, quickly press L/OUT while the channel is displayed.
  To Unlock a channel, See Locking/Unlocking Search Frequencies.
  To turn the Delay on or off for a channel, quickly press DELAY while the channel is displayed. dly will turn to DLY in the display when the delay is on..
  To change the Receive Mode, (FRS-SR2 only) press MODE to select a different mode. The receive mode will go to 'small' letters in the display until you press FUNC then MODE to reset the scanner to receive the default mode for the band.
  To Attenuate a channel, quickly press ATT while the channel is displayed. att will turn to ATT in the display when the attenuator is on for the channel.
  To Copy a frequency into a channel, quickly press FUNC then PGM. Then see Frequency Copy.
  To Copy a frequency into the priority channel (not with Marine-SR0), quickly press FUNC then PRI while the channel is displayed. The display will flash twice and the frequency will be copied into the priority channel.
To exit searching, press MAN or SCAN.

Police/Fire, Air, or Amateur Search Contents
To start a Police/Fire (SR3), Air (SR4), or Amateur (SR5) search, press SRCH until you find the desired band and the scanner should start searching automatically. In the Air band only, pressing FUNC then will restart searching up from the lowest frequency. Pressing FUNC then will restart searching down from the highest frequency.
 
  To change search directions or continue searching, press the or button. An arrow in the upper left of the display shows the direction.
  To turn the Seek feature on or off, press FUNC then 7 while searching. Seek ON or OFF will briefly appear on the bottom line. will appear in the right of the display when the 'seek' feature is on.
  To Pause on a frequency, quickly press PSE to stop searching. **PAUSED** appears in the display. To resume searching, press PSE again.
  To Step through the frequencies one at a time, press PSE. Press the or button to step through the frequencies. To resume searching, press PSE again.
 
To Lock out a frequency, quickly press L/OUT when the scanner stops on the frequency.
  To Unlock a frequency, See Locking/Unlocking Search Frequencies.
  To turn band groups on or off, in the Police/Fire (SR3) and Amateur (SR5) bands press the number keys (0-3 or 0-5) to select the group. See also Search Band Charts.
  To Attenuate a band group, in the Police/Fire (SR3) or Amateur (SR5) bands, press ATT while the group is being searched. att will turn to ATT in the display when the attenuator is on.
  To turn the Delay on for the band, press DELAY to pause before searching resumes after the transmission ends. dly will turn to DLY in the display when the delay is on.
  To change the Receive Mode, (not in Air-SR4) press MODE to select a different mode. The receive mode will go to 'small' letters in the display until you press FUNC then MODE to reset the scanner to receive the default mode for the band.
  To turn Zeromatic Tuning on or off for the band, press FUNC then 0.
  To Copy a frequency into a channel, quickly press FUNC then PGM. Then see Frequency Copy.
  To Copy a frequency into the priority channel, quickly press FUNC then PRI while the channel is displayed. The display will flash twice and the frequency will be copied into the priority channel.
To exit searching, press MAN or SCAN.

Search Band Charts Contents
SR3 Police/Fire band
Receive modes: FM,CT,DC
Grp Frequency Step
0 33.420-33.980 20
37.020-37.420 20
39.020-39.980 20
42.020-42.940 20
44.620-45.860 40
45.880  
45.900
45.940-46.060 40
1 153.770-154.130 15
154.145-154.445 15
155.010-155.370 60
155.415-155.700 15
155.730-156.210 60
158.730-159.210 60
166.250  
170.150
2 453.0375-453.9625 12.5
458.0375-458.9625 12.5
460.0125-460.6375 12.5
465.0125-465.6375 12.5
3 851.0125-860.9875 25
866.0125-868.9875 12.5
SR4 Aircraft
Receive modes: AM
Frequency Step
108-136.99166 8.33
SR5 Amateur Bands
Receive modes: FM,CT,DC
Grp Frequency Step
0 28.0-29.7 5
1 50-54 5
2 144-148 5
3 222-225 5
4 420-450 12.5
5 1240-1300 6.25
SR0 Marine band
Receive mode: FM
Ch. Frequency Ch. Frequency Ch. Frequency Ch. Frequency
1 156.050 19 156.950 28 162.000 78 156.925
5 156.250 20 157.000 63 156.175 79 156.975
6 156.300 20 161.600 64 156.225 80 157.025
7 156.350 21 157.050 64 160.825 81 157.075
8 156.400 22 157.100 65 156.275 82 157.125
9 156.450 23 157.150 66 156.325 83 157.175
10 156.500 24 157.200 67 156.375 84 157.225
11 156.550 24 161.800 68 156.425 84 161.825
12 156.600 25 157.250 69 156.475 85 157.275
13 156.650 25 161.850 70 156.525 85 161.875
14 156.700 26 157.300 71 156.575 86 157.325
15 156.750 26 161.900 72 156.625 86 161.925
16 156.800 27 157.350 73 156.675 87 157.375
17 156.850 27 161.950 74 156.725 87 161.975
18 156.900 28 157.400 77 156.875 88 157.425
SR1 CB band
Receive mode: AM
Ch. Frequency Ch. Frequency
1 26.965 21 27.215
2 26.975 22 27.225
3 26.985 23 27.255
4 27.005 24 27.235
5 27.015 25 27.245
6 27.025 26 27.265
7 27.035 27 27.275
8 27.055 28 27.285
9 27.065 29 27.295
10 27.075 30 27.305
11 27.085 31 27.315
12 27.105 32 27.325
13 27.115 33 27.335
14 27.125 34 27.345
15 27.135 35 27.355
16 27.155 36 27.365
17 27.165 37 27.375
18 27.175 38 27.385
19 27.185 39 27.395
20 27.205 40 27.405
SR2 FRS/GMRS/MURS
Receive modes: FM,CT,DC
Ch. Frequency Ch. Frequency
1 462.5625 15 462.550
2 462.5875 16 462.575
3 462.6125 17 462.600
4 462.6375 18 462.625
5 462.6625 19 462.650
6 462.6875 20 462.675
7 462.7125 21 462.700
8 467.5625 22 462.725
9 467.5875 23 151.820
10 467.6125 24 151.880
11 467.6375 25 151.940
12 467.6625 26 154.570
13 467.6875 27 154.600
14 467.7125

Seek Function
When the seek function is on, the scanner will stay on a frequency for up to 5 seconds then automatically continue searching.
  To turn the Seek feature on or off, press FUNC then 7 while searching. Seek ON or OFF will briefly appear on the bottom line. will appear in the right of the display when the 'seek' feature is on.
  Note: The seek feature does not work during a Tune search.

Limit Search Contents
To Program a Limit Search, press PGM then SRCH. Enter SR6 Search appears at the top and the previous lower and upper search limits are shown. Enter the lower limit frequency then press ENT. Enter the upper limit frequency then press ENT. Press SRCH to start searching.
 
To Start a Limit Search, press SRCH until Limit Search appears in the display. The scanner should start searching. Pressing FUNC then will restart searching up from the lowest frequency. Pressing FUNC then will restart searching down from the highest frequency.
 
  To Text Tag a limit search, See Text Tagging a Limit Search.
  To change search directions, press the or button. An arrow in the upper left of the display shows the direction.
  To turn the Seek feature on or off, press FUNC then 7 while searching. Seek ON or OFF will briefly appear on the bottom line. will appear in the right of the display when the 'seek' feature is on.
  To Pause on a frequency, quickly press PSE to stop searching and listen to the transmission. **PAUSED** appears in the display. To continue searching, press PSE again.
  To Step through the frequencies one at a time, press PSE. Press the or button to step through the frequencies. To resume searching, press PSE again.
  To Lock out a frequency, quickly press L/OUT while the frequency is displayed.
  To Unlock a frequency, See Locking/Unlocking Search Frequencies.
  To Attenuate the search, press ATT while searching. att will turn to ATT in the display when the attenuator is on.
  To turn the Delay on for the search, press DELAY to pause before searching resumes after the transmission ends. dly will turn to DLY in the display when the delay is on..
  To change the Receive Mode, press MODE to select a different mode. The receive mode will go to 'small' letters in the display until you press FUNC then MODE to reset the scanner to receive the default mode for the band.
  To turn Zeromatic Tuning on or off, press FUNC then 0. The ZM in the display will turn to 'capital' letters when Zeromatic is turned on.
  To Copy a frequency into a channel, quickly press FUNC then PGM. Then see Frequency Copy.
  To Copy a frequency into the priority channel, quickly press FUNC then PRI while the channel is displayed. The display will flash twice and the frequency will be copied into the priority channel.
To exit searching, press MAN or SCAN.

Tune Search Contents
To start a searching at a specific frequency, press TUNE. TUNE and the previous frequency appear in the display and the scanner will automatically start searching. Enter the frequency where you want the scanner to start searching then press ENT to start a new search.

To start a searching at a displayed channel, in manual, pause, or scan mode press FUNC then TUNE. Press PSE to start searching.
 
  To change search directions or resume searching, press the or button. An arrow in the upper left of the display shows the direction.
  To Pause on a frequency, quickly press PSE to stop searching and listen to the transmission. **PAUSED** appears in the display. To continue searching, press PSE again.
  To Step through the frequencies one at a time, press PSE. Press the or button to step through the frequencies. To resume searching, press PSE again.
  To Attenuate the search, press ATT while searching. att will turn to ATT in the display when the attenuator is on.
  To turn the Delay on for the search, press DELAY to pause before searching resumes after the transmission ends. dly will turn to DLY in the display when the delay is on.
  To change the Receive Mode, press MODE to select a different mode. The receive mode will go to 'small' letters in the display until you press FUNC then MODE to reset the scanner to receive the default mode for the band.
  To Copy a frequency into a channel, quickly press FUNC then PGM. Then see Frequency Copy.
  To Copy a frequency into the priority channel, quickly press FUNC then PRI while the channel is displayed. The display will flash twice and the frequency will be copied into the priority channel.
To exit searching, press MAN or SCAN.

Frequency Copy Contents
To Copy a frequency into a specific channel, quickly press FUNC then PGM while receiving a frequency. Store in ChXXX? appears and the frequency will blink. Press the bank number and channel number (ex:002) then ENT to store the channel. It will also store the receive, attenuate, and delay settings. Channel Stored! will appear and the scanner will resume searching.
  Note: You cannot copy a Marine channel into a bank.
  Note: If you try to copy a frequency that is already stored, the scanner beeps 3 times and Dupl.Freq.Chxxx appears. To copy anyway press ENT otherwise press CL to cancel.
To Copy a frequency into the first available channel in bank 9, quickly press FUNC then ENT. Bank 9 Store? appears. Press ENT to copy the frequency into the first available (vacant) channel in bank 9 or, press the desired bank number then ENT to store into the first available channel of the desired bank. Channel Stored! will appear and the scanner will resume searching.
To Copy a frequency into the priority channel, quickly press FUNC then PRI. The display will flash twice and the frequency will be copied into the priority channel.

Zeromatic Tuning
Whenever this feature is turned on, Zeromatic ON briefly appears then zm will turn to ZM and the scanner will tune to the correct center frequency (or the step increment closest to the correct center frequency). When searching with Zeromatic off, ZM turns back to zm and the scanner will unmute faster on a detected signal but the frequency may not be the correct center frequency. Zeromatic works only in search bands SR3, SR4, SR5 and SR6.
  To turn Zeromatic Tuning on or off for the band, press FUNC then 0 when searching.

Locking/Unlocking Search Frequencies
You can skip (lock out) any frequency in search bands SR0-2, and up to 50 frequencies in each of the other search bands SR3-6. This lets you avoid unwanted frequencies or those already stored in a channel.
 
To Lock out a frequency, while searching, press L/OUT when the scanner stops on the frequency. The scanner locks out the frequency and automatically resumes the search.
  Note: If you try to skip more than 50 frequencies, Memory full! appears in the display.
  Note: If you happen to lock out all the frequencies in the search bank and are searching just that bank All ranges Locked out! appears.
To Unlock a single frequency in search bands SR0-2, (Marine, CB, FRS), press SRCH until you find the search band that has the frequency you want to unlock. If the scanner starts to search, press FUNC then SEARCH to stop searching. Press FUNC then L/OUT (each time) to step through the locked out frequencies then press L/OUT to unlock the desired frequency (LO will turn to lo). Press SRCH again to resume searching or MAN to exit.
  Note: If there are no locked out frequencies, the scanner will just beep.
To Unlock a single frequency in search bands SR3-6 (Air, Pol, Amateur, Limit), press SRCH until you find the search band that has the frequency you want to unlock. If the scanner starts to search, press PSE to stop searching. Press FUNC then L/OUT. A locked out frequency and Lockout list appear in the display. If no channels are locked out then No Lockout appears. Press or to find the frequency then press CL to unlock the frequency. Press SRCH to exit the lock out review list.
To Unlock all the locked out frequencies in each search band SR3-6 (Air, Pol, Amateur, Limit), press SRCH until you find the search band you want to clear. If the scanner starts to search, press PSE to stop searching. Press FUNC then L/OUT. A locked out frequency and Lockout 01 of xx appear in the display or No Lockout appears if nothing is locked out. Press FUNC then 6. Clear entire list? Press 1 to clear all, any other key aborts appears. Press 1 to clear all the locked out frequencies or any other key to cancel. List cleared briefly appear in the display. Press SRCH again to resume searching or MAN to exit.
  Note: If all the frequencies in a search bank are locked out you can't clear all the frequencies at the same time.

Weather Radio  

Listening to the Weather Band Contents
To hear your local forecast and regional weather information, press WX. The scanner will scan through the weather channels and stop within a few seconds. If it is a weak signal, press WX again to find a stronger channel.
Press MAN or SCAN to exit.

Receiving SAME Weather Alerts  
The weather service precedes each weather alert with a digitally-encoded SAME (Specific Area Message Encoding) signal, then a 1050 Hz tone. You can set the scanner to decode and display the SAME message when an alert is broadcast. Then if you are monitoring a weather channel with a digitally-encoded SAME signal when an alert is broadcast, the scanner will show the type of alert being broadcast such as Warning, Watch, Statement, or Test Message. The scanner will also sound alternating alert tones and display Weather ALERT when the scanner receives a 1050 Hz tone. The scanner does not display the actual messages. It uses only the alert portion of the SAME signal (Warning, Watch, Statement, or Test Message). To scan and receive alerts, set the weather channel as the priority channel.

For the purpose of broadcasting weather information, the NWS has divided the United States into regions by state and county (or parish, where applicable) then assigned a 6-digit FIPS code to identify each county or parish. For example, the code for Tarrant County, Texas, is 048439. The first digit in a FIPS code identifies the county subdivision, the next two digits identify the state, and the last three digits identify the county or parish. Most FIPS codes begin with 0, which means the code represents an entire county. The NWS, however, plans to eventually subdivide some large counties. When that happens, each subdivision will be assigned a digit from 1-9, resulting in codes such as 148439, 248439, and so on.

To obtain the FIPS code for the location where you installed your scanner call the NWS toll free at 1-888-697-7263 (follow the instructions you hear) or see
FIP codes for the United States and its Possessions.

FIPS codes are in the format nSSCCC:

n: A special subcounty designator. For an entire county, use 0.
SS: The state code.
CCC: The county code.
 
To turn on the weather alert, while listening to a weather channel, press FUNC then WX. FIPS: ALL Codes and SAME Standby appear. All codes will be received if none are programmed(?). The scanners sound will mute and wait for a tone. When the scanner receives an alert, it will beep for 5 minutes or until you press any key (except lit light/key symbol). If, after 5 minutes no key has been pressed, the scanner will beep every ten seconds. If the scanner receives a new alert after 5 minutes, the scanner will again beep for 5 minutes or until you press any key. Pressing any key will ready the scanner for another tone.
To test the alert tones, with the alert on, press and hold WX. The scanner will cycle through the different beeps every 3 seconds showing the corresponding alerts on the display. Press any key to cancel.
To turn off the weather alert, press FUNC then WX. DIG WX STBY and CANCEL: F+WX disappear. The scanner will resume receiving the weather channel.
To program a weather channel as the priority channel, press WX. Select the weather channel you want to use as the priority channel then press FUNC and PRI. If you program a weather channel as the priority channel, the scanner stays in the priority channel only when the scanner detects the weather alert tone. In this mode all alerts are received. FIPS settings are ignored.
To program specific FIP codes, press WX to put the scanner in weather search mode.
  Press FUNC then PGM and you will see FIPCode Setting.
  Press or to select the location number (0-9).
  Enter the FIP code and press ENT. Press L/OUT to lockout the code if you wish.
To clear a code press FUNC then CL (Clear).
  If you want to tag the code press TEXT. See Entering Characters.
  Press or to select the next code location to program more codes.
  Press WX to exit.
To review stored FIP codes, press WX then the location number (0-9).
Press MAN or SCAN to exit.

Skywarn Programming  
Many areas of the country have amateur radio repeaters that have been designated as Skywarn repeaters. During times of severe weather, these repeaters are used to relay reports of severe weather directly to meteorologists at a local National Weather Service (NWS) forecast office. Using the Skywarn feature in your scanner, you can easily jump to one of three Skywarn repeater frequencies and monitor these reports, in many cases hearing about severe weather in your area instantly as it occurs. This function lets you quickly move to the skywarn channels (channels 997 through 999) from any mode except SAME standby mode. To see a partial list of state Skywarn frequencies go to the Scanning Reference weather site here.
 
To use the Skywarn feature, program up to 3 Skywarn frequencies in channels 997-999 (use FM mode). See Programming Conventional Channels.
  Press and hold WX for about 1 second. You will see Skywarn-1 on the bottom line.
  Pressing or will search through the 3 Skywarn channels.
Press MAN or SCAN to exit.

Special Features  

Text Tagging Contents
You can program text tags (up to 16 characters) for a limit search and each channel, bank, or ID. You can also reprogram the startup screen with 4 lines of text.

To Text Tag a Limit Search:
1. Press PGM then SRCH. Enter SR6 Search and the previous lower and upper search limits are shown in the display.
2. Press TEXT. Move the cursor to the position you want using to move right, or to move left, then skip to Entering Characters.

To Text Tag a Bank:
1. In Manual mode press PGM.
2. Press FUNC then the bank number (0-9) then TEXT. Move the cursor to the position you want using to move right, or to move left, then skip to Entering Characters.

To Text Tag a Channel:
1. In Manual mode, select the channel by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel.
2. Press PGM then TEXT.
3. Move the cursor to the position you want using to move right, or to move left, then skip to Entering Characters.

To Text Tag an ID:
1. In Manual mode select any channel of the bank you want to text tag an ID in by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel. You will see the bank number (0-9), list number (0-4), and the list status (ON or OFF) on the top line, (the ID on the second line, and the ID tag on the third line if programmed).
2. Press TRUNK (each time) to select the ID list (0-4).
3. Select the ID# (0-29) by pressing or (or press and hold; faster).
4. Press TEXT. Move the cursor to the position you want using to move right, or to move left, then skip to Entering Characters.
 
To Text Tag the Startup Screen:
1. In Manual mode press PGM then FUNC then TEXT.
2. Move the cursor to the position you want using to move right, or to move left, then skip to Entering Characters.
3. Press ENT to edit the next line.
4. Return to step 2 for the rest of the lines.
Press MAN
to exit programming.

Entering Characters:
Press FUNC then CL to clear the existing tag if desired.
To insert a space, press . (period) or
.
Select each letter by pressing the corresponding number key below each letter (2 for A,B,or C). The display will then show the available letters.
 Select 1 for the first letter, 2 for the second letter, 3 for the third letter, or 4 for the fourth letter.

To toggle between capital and small letters, at any time, press FUNC.
To insert a number, press 1 first, then enter the desired number.
To insert a special character, press 0 first, (then FUNC if you want to see the second set of characters) then the number of the desired character.
If you want to clear the existing character, place the cursor on the character and press CL.
Press ENTER when finished to store the tag. Press MAN to exit programming.

Turning The Keytone Off/On Contents
You have the option of turning the key conformation tone off or on (to confirm that the keys have been pressed). The keypad area is kind of small so some of us with big fingers, afraid that they have pressed more than one key at a time, might appreciate this. This will also kill the annoying 'battery low' beep every 2 seconds.
 
To turn the Keytone off, turn off the scanner. Turn on the scanner and press 2 while the welcome screen is displayed. Key-tone ON will briefly appear.
To turn the Keytone on, turn off the scanner. Turn on the scanner and press 1 while the welcome screen is displayed. Key-tone OFF will briefly appear.

Using The Display Backlight (97)  
There are three backlight modes you can choose from to control backlight activation, Normal mode, Keypress mode, and first Keypress Ignore mode.
Normal Mode:
 

Press . The backlight will turn on for the factory default setting of 5 seconds. The backlight continues to remain on while you are operating the keypad.
To turn off the backlight before it automatically turns off, press again.

Keypress Mode:
 

In Keypress mode, the backlight will light automatically when you press any key on the keypad, and function as described in Normal mode.
This mode is useful if you want the backlight to come on automatically when you perform an operation using the keypad.

Ignore Mode:
 

With Ignore mode, the backlight functions as described in Keypress mode, except that the scanner ignores the first keypress.
This mode is useful when you wish to quickly illuminate the display and keypad without having to search for the
key.
The first keypress is ignored, and the scanner sounds the low pitched error beep to remind you that the first key pressed to activate the backlight is ignored by the scanner.

In any backlight mode, you can press and hold for about 1 second to force the backlight on full time. Press while the backlight is on to turn it off.

To Change the Backlight Mode:
Turn the scanner off then back on again. While viewing the welcome screen, press . Press or to select:
  3, 5, 10, or 20 seconds for normal mode.
  K3, K5, K10, or K20 seconds for Keypress Mode.
  I3, I5, I10, or I20 seconds for Ignore Mode.
  Then press ENT to store the setting.
 
Using The Dimmer (2055)  

Press DIM to adjust the brightness of the display backlight to dark, light off, or light.

Changing the Display Contrast  
In Manual mode, press FUNC then 9. Use Up/Down keys to set contrast appears. Press or to select the contrast then press ENT.

Using The Keylock (2055) Contents
Once you program your scanner, you can protect it from accidental program changes by turning on the key lock feature. When the keypad is locked, the only keys that operate are FUNC, SQ, VOLUME, and .
 
To turn on the Keylock, press FUNC then . Key locked appears for about 1 second. Key locked appears when you press any key.
To turn off the Keylock, press FUNC then . The scanner beeps 3 times and Key unlocked appears.

Cloning/Uploading/Downloading  
You can transfer the programmed data to and from another Pro-97/2055 using an optional connecting cable with a 1/8 -inch mono plug on both ends. You can also upload data from your computer to the scanner with an (optional) one-way cable, or upload/down data to/from your computer with an (optional) two-way cable (or optional USB cable) and the Win97 software.
 
To Clone one scanner to another, turn on both scanners. Connect the interface cable to the PC/IF jack on each scanner. *CLONE MODE* UP to send, remove cable to exit appears. Press on the sending scanner. Confirm send data? 1= YES Press other key for NO appears. Press 1 to send or any other key to cancel. *CLONE MODE* Receiving... and a progress bar will appear while transferring. When the transfer is complete, *CLONE MODE* UP to send, remove cable to exit will re-appear and you can disconnect the cables.
To Upload/Download to/from your computer, turn on the scanner. Connect the interface cable to the PC/IF jack on the scanner. Click on 'Scanner' in the menu bar of the software then 'Upload to Scanner' or 'Download from Scanner'. *CLONE MODE* Receiving... and a progress bar will appear while transferring. When the transfer is complete, *CLONE MODE* UP to send, remove cable to exit will re-appear and you can disconnect the cable.

Scanner Reset  
If the scanner's display locks up or does not work properly after you connect a power source, you might need to reset or initialize it. If you have problems with the scanner, first try to reset it to retain the memory.
  Warning: Initializing the scanner will clear all channel memories and reverts it the state it was in right out of the box.
To Initialize the scanner, turn off the scanner then turn it back on. Press 0 when the welcome screen appears. 'Please select factory tests. Exit if no key is pressed' will briefly appear. Then quickly press 1. 'Initialization clear all memory Enter to confirm Clear to exit' will briefly appear. Quickly press ENT to initialize. 'Initializing, Please stand by' then appears. Do not turn off the scanner while it is initializing. The display should then show M000 on the top line and Bank 0 CH 00 when finished.

Automatic Power Save (97)  
Your scanner features a power save circuit that is automatically activated after about 30 seconds if you have manually select a channel. The power save mode works by allowing the receiver to 'sleep' briefly while waiting for a call on the selected channel and will also turn the backlight off. The power save circuit is disabled when the scanner is tuned to a channel in program mode, scanning, or searching.

Related Links/Info Contents
Using the Repeater Finder Tool
To determine the correct Home Repeater programming, enter the system channels of an LTR system in any order. Be sure to program the mode for each LTR channel to LT. Listen to each channel one at a time in manual mode and watch for the decoded LTR data at the bottom of the scanner's display. When an LTR transmission occurs, you should see the LTR talkgroup information on the bottom line of the display, and a number preceded by 'R' in the bottom right hand corner (i.e., R12). The 'R' number is the Home Repeater number that the current transmission is occurring on. To correctly program this Home Repeater number into your scanner, be sure that the channel number in the bank is equal to the number that is displayed after the 'R'. For example, if you see R12 displayed on a particular LTR frequency, that frequency needs to be programmed into Channel 12 of the current bank in order to track the LTR system activity properly.
 
Finding EDACS LCN order
EDACS frequencies have to be programmed in LCN (Logical Channel Number) order. I have found a procedure at the Trunked Radio Systems User’s Page which explains how to find the LCN order for an EDACS system if you don't know the order. Look for 'Finding EDACS Logical Channel Numbers' by Todd Hartzel near the bottom of the page.
 
Determining Type I Motorola Fleetmaps  
You can try a method I found at Radio Reference.com. Determining Type I Motorola Fleet Maps. by Dave Goodson.
 
Determining Base/Step/Offset for VHF/UHF Motorola Systems
I have found an explanation at Radio Reference.com that describes how to do this if you don't have the information. The Trunked Radio Systems User’s Page also has an explanation. Look for 'Determining Base and Offset Frequencies for the BC245xlt' by John C.
 
Decimal/AFS Conversion Chart
Here is a Conversion Chart to help convert your IDs.

Viewing the Firmware Version
To view the firmware version for the Pro 97/2055 turn on the radio. When viewing the welcome screen press 3. Version 1.01 is the current and only version. No upgrade has ever been released.
 
Finding and reading the date code
The date code or date of manufacture is located inside the battery compartment or on the bottom of the 2055 (Don't rely on the date code on the box). You will see two numbers then a "A" then two more numbers. The first two numbers are the month and the last two are the year. Ex: 01A05 is January of 2005.
Newsgroups and Forums
Yahoo Groups-Pro-97 Radio Reference Forums
Yahoo Groups-Pro-2055 Radio Shack Pro Series Scanners
Yahoo Groups-PRO-2055_scanner Radio Reference Radio Shack Scanners Forum
   
   
Links
Radio Reference.com Radio Reference Data Base
Radio Reference Pro 97 Wiki eHam.net-reviews
Radio Reference Pro 2055 Wiki Scanner Cables
Discriminator tap  
Software
Starrsoft.com-Win97 arc300-Butel software
PSREdit300  

Click here to visit Scanner Master
 
Contents
Last updated October 26, 2019
Home